Pongnas 1000W Induction Heating Board Module - Advanced Heat Dissipation PCB for Voltage Inverter Applications

1. PCB Material: The high frequency induction heater is made of grade PCB with high density and stable performance. 2. High Power: The power line of 1000W induction heating module adopts full copper laying design, which greatly increases the current and generates less heat. 3. Heat Dissipation: Heating PCB board module adopts 100x32x58mm oversized 5 tooth 4 hole high power heat sink for better heat dissipation. 4. High Voltage Output: The output side uses copper columns in parallel, can be connected to other outputs such as high voltage package. 5. 2.54mm Socket: Induction heating board has a 2.54mm socket, after connecting the voltage regulator, plug in the supporting cooling fan and water pump can be used. Specification: Item Type: Induction Heating Board Material: PCB Size: Heating Plate: Approx. 100 x 100mm/3.9 x 3.9in Heat Sink: Approx. 100 x 32 x 58mm/3.9 x 1.3 x 2.3in Input Voltage: 12V-48 Recommended 36V Power Requirements: Less Than 12V≥10A, More Than 15V ≥ 15A Current: 20A Power: 1000W How to Use: 1. Work with a lot of power in addition to the board and components heat, the heat of the copper tube is also very large. Buyers can provide their own water‑cooled cooling system, you can buy a small pump and about 2 meters of inner diameter of 4mm rubber water pipe; you can also buy a package of matching pumps 2. The use of switching power supply must be noted that high‑power switching power supply generally has a slow start function, that is, when the output voltage rises slowly, and if the voltage rises to 12V before the induction heating circuit will be connected because the voltage is not enough to cause the circuit to oscillate, so that the 2 MOS tubes on at the same time and burned components, so be sure to make the switching power supply voltage stability before accessing the induction heating circuit 3. Try not to heat too large volume of metal, otherwise it may be dangerous to overload due to power overload; it is best to add a 20A fuse or ammeter when using 4. Although this driver board can withstand more than 20A current, in order to prevent accidents and damage is recommended not to exceed 48V20A 5. The diameter of the heating is 40mm and the voltage is 24V, if you use more than 30V, you should use a heating with an inner diameter of 50mm or more, the fan and the pump use 12V DC power supply, please supply power separately to avoid burning the fan and the pump Package List: 1 x Induction Heating Board 1 x Heat Conduction Tube Note: 1. The minimum input voltage of this module is 12V does not mean that all 12V power supply can be used, some novice buyers use a power supply with less power, the specific voltage and current of this module have requirements, voltage 12V current must be more than 10A power supply can be used, the power of the power supply is too low will to the actual output voltage of the power supply when the high power output is greatly reduced, when the voltage is lower than 12V will to two MOS tubes on at the same time, will burn MOS tubes. 2. Some buyers will not pay attention to the power requirements of the power supply when using the MOS tube heating, if found MOS tube heating abnormal then first consider whether the power supply output to meet the requirements 3. The board should not be idle, otherwise it will make a high frequency noise, and then the MOS tube will heat up and burn out 4 induction heating recommended the use of 36V20A power supply, 12V power supply is too small heating almost no response, and 12V power supply heating easily to lower power supply output voltage, below 12V is very dangerous 5. Induction heating power is very large, heat is inevitable, be sure to do a good job of heat dissipation. 6. Do induction heating should use the copper tube matched with this product, or winding in accordance with the standard of 8 turns with an inner diameter of 40mm, otherwise the buyer is responsible for any burning problems. 7. Please allow some errors due to manual measurement.

• 【High Stability】 - The 1000W high-frequency induction heating board module is crafted with -grade PCB, ensuring high density and unmatched stability during . This robustness allows for consistent heating performance, making it ideal for various applications, from metalworking to culinary tasks, increasing efficiency in any project.
• 【Enhanced Power Design】 - Our induction heating module utilizes a full copper laying design for the power line, maximizing current while minimizing heat generation. This innovative approach allows your system to maximize its energy efficiency, ensuring that you achieve remarkable heating results without the of overheating, which enhances your operational .
• 【Superior Heat Dissipation】 - Engineered with an oversized heat sink measuring 100x32x58mm, the heating PCB board module offers exemplary heat dissipation performance. The five-tooth, four-hole design effectively spreads out heat, excessive temperature buildup, thereby prolonging the module's lifespan and ensuring you can work without interruption or concern.
• 【Versatile Connectivity】 - Equipped with three parallel M4 copper columns on the output side, this induction heating board allows integration with various high-voltage outputs, such as high voltage packages. This feature provides flexibility for users looking to customize their systems, making it an indispensable component for tech enthusiasts and professionals alike.
• 【Convenient Socket】 - Featuring a 2.54mm socket, this induction heating board simplifies connectivity to a variety of devices. Once connected to the voltage regulator, you can easily plug in a cooling fan and pump, ensuring optimal performance and maintaining during high-powered operations, which is for extensive heating applications.